Loading Events

« All Events

  • This event has passed.

Basic Auto Electrics, Electronics & Diagnostics Skills

January 15 @ 09:00 - February 2 @ 04:30 EAT

45,000KES

Basic Auto Electrics, Electronics & Diagnostics Skills

This course consists of THREE units namely:

Unit 1: Introduction to Basic Electronics

Unit 2: Scantool Diagnostics & CAN Bus

Unit 3: Engine Component Diagnostics

Each of the units costs 15K (USD 150) and takes 1 Week to complete. The full course takes 3 weeks and costs USD 450. It is advisable to take up all the units if one is novice (beginner). Those already with qualifications and skills may skip the basics upon being preliminary examined for their experience.

 

Venue: Kenvision Techniks Workshops, Kahawa Sukari

Fee: USD 450 (full course) /or USD 150 per unit

Date: Dec 04 – 22,  2017

Click HERE to book this course

 

Working on cars with experience

Modern car parts

 

 

 

Unit 1: Introduction to Basic Electronics

All technicians would benefit from attending this course, particularly people who would normally avoid working with electrics.

Some older technicians may have just attended mechanical training when young and not had formal electrical training.

  • How electricity is produced for vehicles
  • Wiring types for various circuits
  • A/C & D/C differences
  • Measurements, Volts, Amps & Ohms
  • Ohms Law
  • Electrical units and multipliers
  • Circuits, series and parallel
  • Switches and Rheostats
  • Measuring devices
  • Practical Exercises
  • Grounds, and Earth testing
  • Introduction to Sensors and Actuators
  • Fault finding techniques, including short and open circuit testing and measuring high resistances

Click HERE to book this course

Click Here to Download the Course Outline: AUTO-ELECTRICS TRAINING

Getting it right with the right tools

Unit 2: Scantool Diagnostics & CAN Bus

KES15K/Person

All technicians would benefit from this course, basic trained mechanics will gain the knowledge and insight required to work on modern cars, understanding limitations of equipment types will build confidence to correctly diagnose complex problems on today’s cars.

Technicians who wish to be brought up to date on how to diagnose faults on modern vehicles.

People who need to know how the system works, to facilitate other areas of work they may need the knowledge.

  • Timeline on introduction of computerisation and vehicle networks
  • Electric fundamentals
  • Understanding Fault Codes and how they are generated
  • Why you do not always get Fault Codes but have problems on the vehicle
  • Sensors and Actuators, what role they play.
  • How data is passed around a vehicle.
  • Understand the difference between Live Data and Graphing
  • CAN BUS explained
  • Why we need and use CAN BUS systems

 

                                       car scan tool

Click Here to Download the Course Outline: AUTO-ELECTRICS TRAINING

Click HERE to book this course

Unit 3: Engine Component Diagnostics

KES 15K/Person

This course is orientated to use oscilloscope with other test equipment. In particular the oscilloscope helps give a good understanding of sensors, actuators and how they operate.

Fundamentals of electronic ignition, electronic control systems, electronic fuel injection and idle speed control; with oscilloscope use as a diagnostic aid. With waveform interpretation and understanding made easy.

TARGET GROUP

  1. All technicians would benefit from attending this course but it is specifically aimed at technicians who understand the basic principles of electricity and want to improve their diagnostic skills.
  2. Anyone who has finally realized that owning a Scan-tool is only halfway there. For people who want to fix the car rather than just find out what is wrong with it.
  3. Fundamentals on electronic controls used, focusing on electronic architecture and interaction between sensors and actuators.
  4. Background to purpose of Euro 3, Euro 4, Euro 5 and what to expect with Euro 6. Block exemption rulings and roll-out of standardized parts.
  5. Detailed coverage of Electronic Fuel Injection both Petrol and Diesel.

Click Here to Download the Course Outline: AUTO-ELECTRICS TRAINING

SENSORS

  • Air metering devices including vacuum sensors (MAP), hot wire (air mass meter),
  • Karmen Vortex type air flow and vane type air flow meters.
  • Temperature sensors
  • Oxygen sensors (Lambda/O2)
  • Knock sensors16
  • Throttle position sensors (Potentiometers)
  • Engine speed sensors (Crankshaft)
  • Crank/Cam position sensor (Cam sensor)
  • ELECTRONIC CONTROL UNITS (ECU)
  • Basic operation and operational decision making priorities.
  • ACTUATORS
  • Fuel injectors
  • Idle Speed Control Valves (Rotary and Electromagnetic)
  • Exhaust Gas Recirculation Valves (EGR)

PRACTICAL – Implementation of the theory using either delegates own vehicles and test equipment, if required equipment shall be provided for this practical work. Readings can be compared with Scan-tool data

Certificate offered by Kenvision Techniks in conjunction with Beam Auto

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Save

Organiser

Kenvision Trainers, Kahawa Sukari, Nairobi
Phone:
+254 725579251
Email:
ken_trainers@kenvisiontechniks.com
Website:
www.kenvisiontechniks.com

Venue

Kenvision Techniks Institute
Q7-Q9 FELIZ BUILDING- KAHAWA SUKARI
NAIROBI, NAIROBI 00200 Kenya
+ Google Map
Phone:
254 (0)20 5295138 / 731 983372 / 725 579251
Website:
https://kenvisiontechniks.com
Facebook Auto Publish Powered By : XYZScripts.com